/**
 * \file
 *
 * \brief USB configuration file
 *
 * Copyright (c) 2009-2018 Microchip Technology Inc. and its subsidiaries.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Subject to your compliance with these terms, you may use Microchip
 * software and any derivatives exclusively with Microchip products.
 * It is your responsibility to comply with third party license terms applicable
 * to your use of third party software (including open source software) that
 * may accompany Microchip software.
 *
 * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES,
 * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE,
 * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
 * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE
 * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
 * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
 * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
 * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE.  TO THE FULLEST EXTENT
 * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY
 * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
 * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="https://www.microchip.com/support/">Microchip Support</a>
 */

#ifndef _CONF_USB_H_
#define _CONF_USB_H_

#include "compiler.h"
//#include "main.h"

//#warning You must refill the following definitions with a correct values

/**
 * USB Device Configuration
 * @{
 */

//! Device definition (mandatory)
#define  USB_DEVICE_VENDOR_ID             0xDC29
#define  USB_DEVICE_PRODUCT_ID            0xDC29
#define  USB_DEVICE_MAJOR_VERSION         1
#define  USB_DEVICE_MINOR_VERSION         0
#define  USB_DEVICE_POWER                 100 // Consumption on VBUS line (mA)
#define  USB_DEVICE_ATTR                  \
(USB_CONFIG_ATTR_BUS_POWERED)
//		(USB_CONFIG_ATTR_SELF_POWERED)
 
// (USB_CONFIG_ATTR_REMOTE_WAKEUP|USB_CONFIG_ATTR_SELF_POWERED)
// (USB_CONFIG_ATTR_REMOTE_WAKEUP|USB_CONFIG_ATTR_BUS_POWERED)

//! USB Device string definitions (Optional)
#define  USB_DEVICE_MANUFACTURE_NAME      "MK Factor"
#define  USB_DEVICE_PRODUCT_NAME          "DEF CON 29 Badge"
#define  USB_DEVICE_SERIAL_NAME			  "12345"
//#define  USB_DEVICE_SERIAL_NAME           *(volatile uint32_t *)0x0080A00C //"12345" // Disk SN for MSC

/**
 * Device speeds support
 * @{
 */
//! To define a Low speed device
//#define  USB_DEVICE_LOW_SPEED

//! To authorize the High speed
#if (UC3A3||UC3A4)
//#define  USB_DEVICE_HS_SUPPORT
#endif
//@}

/**
 * USB Device Callbacks definitions (Optional)
 * @{
 */
#define  UDC_VBUS_EVENT(b_vbus_high)      user_callback_vbus_action(b_vbus_high)
extern void user_callback_vbus_action(bool b_vbus_high);
#define  UDC_SOF_EVENT()                  user_callback_sof_action()
extern void user_callback_sof_action(void);
// #define  UDC_SUSPEND_EVENT()              user_callback_suspend_action()
// extern void user_callback_suspend_action(void);
// #define  UDC_RESUME_EVENT()               user_callback_resume_action()
// extern void user_callback_resume_action(void);
//! Mandatory when USB_DEVICE_ATTR authorizes remote wakeup feature
// #define  UDC_REMOTEWAKEUP_ENABLE()        user_callback_remotewakeup_enable()
// extern void user_callback_remotewakeup_enable(void);
// #define  UDC_REMOTEWAKEUP_DISABLE()       user_callback_remotewakeup_disable()
// extern void user_callback_remotewakeup_disable(void);
//! When a extra string descriptor must be supported
//! other than manufacturer, product and serial string
// #define  UDC_GET_EXTRA_STRING()
//@}

extern bool main_cdc_enable(uint8_t port);
extern void main_cdc_disable(uint8_t port);
extern void main_cdc_set_dtr(uint8_t port, bool b_enable);

/**
 * USB Device low level configuration
 * When only one interface is used, these configurations are defined by the class module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Control endpoint size
#define  USB_DEVICE_EP_CTRL_SIZE       64

//! Number of interfaces for this device
#define  USB_DEVICE_NB_INTERFACE       3 // 1 or more

//! Total endpoint used by all interfaces
//! Note:
//! It is possible to define an IN and OUT endpoints with the same number on XMEGA product only
//! E.g. MSC class can be have IN endpoint 0x81 and OUT endpoint 0x01
#define  USB_DEVICE_MAX_EP             4 // 0 to max endpoint requested by interfaces
//@}

//@}


/**
 * USB Interface Configuration
 * @{
 */

/**
 * Configuration of CDC interface (if used)
 * @{
 */

//! Number of communication port used (1 to 3)
#define  UDI_CDC_PORT_NB 1

//! Interface callback definition
/*#define  UDI_CDC_ENABLE_EXT(port)             true
#define  UDI_CDC_DISABLE_EXT(port)
#define  UDI_CDC_RX_NOTIFY(port)
#define  UDI_CDC_TX_EMPTY_NOTIFY(port)
#define  UDI_CDC_SET_CODING_EXT(port,cfg)
#define  UDI_CDC_SET_DTR_EXT(port,set)
#define  UDI_CDC_SET_RTS_EXT(port,set)*/

#define  UDI_CDC_ENABLE_EXT(port)         main_cdc_enable(port)
#define  UDI_CDC_DISABLE_EXT(port)        main_cdc_disable(port)
#define  UDI_CDC_RX_NOTIFY(port)          //uart_rx_notify(port)
#define  UDI_CDC_TX_EMPTY_NOTIFY(port)
#define  UDI_CDC_SET_CODING_EXT(port,cfg) //uart_config(port,cfg)
#define  UDI_CDC_SET_DTR_EXT(port,set)    main_cdc_set_dtr(port,set)
#define  UDI_CDC_SET_RTS_EXT(port,set)

/*
 * #define UDI_CDC_ENABLE_EXT(port) my_callback_cdc_enable()
 * extern bool my_callback_cdc_enable(void);
 * #define UDI_CDC_DISABLE_EXT(port) my_callback_cdc_disable()
 * extern void my_callback_cdc_disable(void);
 * #define  UDI_CDC_RX_NOTIFY(port) my_callback_rx_notify(port)
 * extern void my_callback_rx_notify(uint8_t port);
 * #define  UDI_CDC_TX_EMPTY_NOTIFY(port) my_callback_tx_empty_notify(port)
 * extern void my_callback_tx_empty_notify(uint8_t port);
 * #define  UDI_CDC_SET_CODING_EXT(port,cfg) my_callback_config(port,cfg)
 * extern void my_callback_config(uint8_t port, usb_cdc_line_coding_t * cfg);
 * #define  UDI_CDC_SET_DTR_EXT(port,set) my_callback_cdc_set_dtr(port,set)
 * extern void my_callback_cdc_set_dtr(uint8_t port, bool b_enable);
 * #define  UDI_CDC_SET_RTS_EXT(port,set) my_callback_cdc_set_rts(port,set)
 * extern void my_callback_cdc_set_rts(uint8_t port, bool b_enable);
 */

//! Define it when the transfer CDC Device to Host is a low rate (<512000 bauds)
//! to reduce CDC buffers size
#define  UDI_CDC_LOW_RATE

//! Default configuration of communication port
#define  UDI_CDC_DEFAULT_RATE             115200
#define  UDI_CDC_DEFAULT_STOPBITS         CDC_STOP_BITS_1
#define  UDI_CDC_DEFAULT_PARITY           CDC_PAR_NONE
#define  UDI_CDC_DEFAULT_DATABITS         8

//! Enable id string of interface to add an extra USB string
#define  UDI_CDC_IAD_STRING_ID            4

/**
 * USB CDC low level configuration
 * In standalone these configurations are defined by the CDC module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoints' numbers used by single or first CDC port
#define  UDI_CDC_DATA_EP_IN_0          (1 | USB_EP_DIR_IN)  // TX
#define  UDI_CDC_DATA_EP_OUT_0         (2 | USB_EP_DIR_OUT) // RX
#define  UDI_CDC_COMM_EP_0             (3 | USB_EP_DIR_IN)  // Notify endpoint
//! Endpoints' numbers used by second CDC port (Optional)
#define  UDI_CDC_DATA_EP_IN_2          (4 | USB_EP_DIR_IN)  // TX
#define  UDI_CDC_DATA_EP_OUT_2         (5 | USB_EP_DIR_OUT) // RX
#define  UDI_CDC_COMM_EP_2             (6 | USB_EP_DIR_IN)  // Notify endpoint
//! Endpoints' numbers used by third CDC port (Optional)
#define  UDI_CDC_DATA_EP_IN_3          (7 | USB_EP_DIR_IN)  // TX
#define  UDI_CDC_DATA_EP_OUT_3         (8 | USB_EP_DIR_OUT) // RX
#define  UDI_CDC_COMM_EP_3             (9 | USB_EP_DIR_IN)  // Notify endpoint

//! Interface numbers used by single or first CDC port
#define  UDI_CDC_COMM_IFACE_NUMBER_0   0
#define  UDI_CDC_DATA_IFACE_NUMBER_0   1
//! Interface numbers used by second CDC port (Optional)
#define  UDI_CDC_COMM_IFACE_NUMBER_2   2
#define  UDI_CDC_DATA_IFACE_NUMBER_2   3
//! Interface numbers used by third CDC port (Optional)
#define  UDI_CDC_COMM_IFACE_NUMBER_3   4
#define  UDI_CDC_DATA_IFACE_NUMBER_3   5
//@}
//@}


/**
 * Configuration of MSC interface (if used)
 * @{
 */
//! Vendor name and Product version of MSC interface
#define UDI_MSC_GLOBAL_VENDOR_ID            \
   'A', 'T', 'M', 'E', 'L', ' ', ' ', ' '
#define UDI_MSC_GLOBAL_PRODUCT_VERSION            \
   '1', '.', '0', '0'

//! Interface callback definition
//#define  UDI_MSC_ENABLE_EXT()          true
//#define  UDI_MSC_DISABLE_EXT()
//#define  UDI_MSC_NOTIFY_TRANS_EXT()
/*
 * #define UDI_MSC_ENABLE_EXT() my_callback_msc_enable()
 * extern bool my_callback_msc_enable(void);
 * #define UDI_MSC_DISABLE_EXT() my_callback_msc_disable()
 * extern void my_callback_msc_disable(void);
 * #define  UDI_MSC_NOTIFY_TRANS_EXT()    msc_notify_trans()
 * extern void msc_notify_trans(void) {
 */

/**
 * USB MSC low level configuration
 * In standalone these configurations are defined by the MSC module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoint numbers definition
//#define  UDI_MSC_EP_IN                 (1 | USB_EP_DIR_IN)
//#define  UDI_MSC_EP_OUT                (2 | USB_EP_DIR_OUT)

//! Interface number
//#define  UDI_MSC_IFACE_NUMBER          0
//@}
//@}


/**
 * Configuration of HID Mouse interface (if used)
 * @{
 */
//! Interface callback definition
//#define  UDI_HID_MOUSE_ENABLE_EXT()       true
//#define  UDI_HID_MOUSE_DISABLE_EXT()
// #define UDI_HID_MOUSE_ENABLE_EXT() my_callback_mouse_enable()
// extern bool my_callback_mouse_enable(void);
// #define UDI_HID_MOUSE_DISABLE_EXT() my_callback_mouse_disable()
// extern void my_callback_mouse_disable(void);

/**
 * USB HID Mouse low level configuration
 * In standalone these configurations are defined by the HID Mouse module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoint numbers definition
//#define  UDI_HID_MOUSE_EP_IN           (1 | USB_EP_DIR_IN)

//! Interface number
//#define  UDI_HID_MOUSE_IFACE_NUMBER    0
//@}
//@}


/**
 * Configuration of HID Keyboard interface (if used)
 * @{
 */
//! Interface callback definition
#define  UDI_HID_KBD_ENABLE_EXT()       true
#define  UDI_HID_KBD_DISABLE_EXT()
// #define UDI_HID_KBD_ENABLE_EXT() my_callback_keyboard_enable()
// extern bool my_callback_keyboard_enable(void);
// #define UDI_HID_KBD_DISABLE_EXT() my_callback_keyboard_disable()
// extern void my_callback_keyboard_disable(void);
#define  UDI_HID_KBD_CHANGE_LED(value)
// #define  UDI_HID_KBD_CHANGE_LED(value) my_callback_keyboard_led(value)
// extern void my_callback_keyboard_led(uint8_t value)

/**
 * USB HID Keyboard low level configuration
 * In standalone these configurations are defined by the HID Keyboard module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoint numbers definition
#define  UDI_HID_KBD_EP_IN           (4 | USB_EP_DIR_IN)

//! Interface number
#define  UDI_HID_KBD_IFACE_NUMBER    2
//@}
//@}


/**
 * Configuration of HID Generic interface (if used)
 * @{
 */
//! Interface callback definition
#define  UDI_HID_GENERIC_ENABLE_EXT()       true
#define  UDI_HID_GENERIC_DISABLE_EXT()
#define  UDI_HID_GENERIC_REPORT_OUT(ptr)
#define  UDI_HID_GENERIC_SET_FEATURE(f)
/*
 * #define UDI_HID_GENERIC_ENABLE_EXT() my_callback_generic_enable()
 * extern bool my_callback_generic_enable(void);
 * #define UDI_HID_GENERIC_DISABLE_EXT() my_callback_generic_disable()
 * extern void my_callback_generic_disable(void);
 * #define  UDI_HID_GENERIC_REPORT_OUT(ptr) my_callback_generic_report_out(ptr)
 * extern void my_callback_generic_report_out(uint8_t *report);
 * #define  UDI_HID_GENERIC_SET_FEATURE(f) my_callback_generic_set_feature(f)
 * extern void my_callback_generic_set_feature(uint8_t *report_feature);
 */
#define  UDI_HID_REPORT_IN_SIZE             64
#define  UDI_HID_REPORT_OUT_SIZE            64
#define  UDI_HID_REPORT_FEATURE_SIZE        4
#define  UDI_HID_GENERIC_EP_SIZE            64

/**
 * USB HID Generic low level configuration
 * In standalone these configurations are defined by the HID generic module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoint numbers definition
#define  UDI_HID_GENERIC_EP_OUT   (2 | USB_EP_DIR_OUT)
#define  UDI_HID_GENERIC_EP_IN    (1 | USB_EP_DIR_IN)

//! Interface number
#define  UDI_HID_GENERIC_IFACE_NUMBER    0
//@}
//@}


/**
 * Configuration of PHDC interface (if used)
 * @{
 */

//! Interface callback definition
#define  UDI_PHDC_ENABLE_EXT()          true
#define  UDI_PHDC_DISABLE_EXT()

//! Select data format of application
//! USB_PHDC_DATAMSG_FORMAT_VENDOR or USB_PHDC_DATAMSG_FORMAT_11073_20601
#define  UDI_PHDC_DATAMSG_FORMAT       USB_PHDC_DATAMSG_FORMAT_11073_20601
//! If USB_PHDC_DATAMSG_FORMAT_11073_20601 then define specialization(s)
#define  UDI_PHDC_SPECIALIZATION       {0x2345} // Define in 11073_20601

//! Defines the QOS need for each transfer direction
#define  UDI_PHDC_QOS_OUT              \
		(USB_PHDC_QOS_MEDIUM_BETTER|USB_PHDC_QOS_HIGH_BEST)
#define  UDI_PHDC_QOS_IN               \
		(USB_PHDC_QOS_LOW_GOOD|USB_PHDC_QOS_MEDIUM_BETTER|USB_PHDC_QOS_MEDIUM_BEST)

//! The following METADATAs can be send during USB enumeration
//! for each endpoints (optional).
//! It can define the Opaque data format of each endpoints
//! These must be up to 253 and recommended <30
#define  UDI_PHDC_METADATA_DESC_BULK_IN   {0x01,0x02,0x03}
#define  UDI_PHDC_METADATA_DESC_BULK_OUT  {0x01,0x02,0x03}
#define  UDI_PHDC_METADATA_DESC_INT_IN    {0x01,0x02,0x03}

/**
 * USB PHDC low level configuration
 * In standalone these configurations are defined by the PHDC module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoint numbers definition
#define  UDI_PHDC_EP_BULK_OUT          (1 | USB_EP_DIR_OUT)
#define  UDI_PHDC_EP_BULK_IN           (2 | USB_EP_DIR_IN)
#if ((UDI_PHDC_QOS_IN&USB_PHDC_QOS_LOW_GOOD)==USB_PHDC_QOS_LOW_GOOD)
// Only if UDI_PHDC_QOS_IN include USB_PHDC_QOS_LOW_GOOD
#  define  UDI_PHDC_EP_INTERRUPT_IN      (3 | USB_EP_DIR_IN)
#endif

//! Endpoint sizes
#define  UDI_PHDC_EP_SIZE_BULK_OUT     32
#define  UDI_PHDC_EP_SIZE_BULK_IN      32
#define  UDI_PHDC_EP_SIZE_INT_IN       8


//! Interface number
#define  UDI_PHDC_IFACE_NUMBER          0
//@}
//@}

/**
 * Configuration of Class Vendor interface (if used)
 * @{
 */

//! Interface callback definition
#define  UDI_VENDOR_ENABLE_EXT()          true
#define  UDI_VENDOR_DISABLE_EXT()
#define  UDI_VENDOR_SETUP_OUT_RECEIVED()  false
#define  UDI_VENDOR_SETUP_IN_RECEIVED()   false
/*
 * #define UDI_VENDOR_ENABLE_EXT() my_callback_vendor_enable()
 * extern bool my_callback_vendor_enable(void);
 * #define UDI_VENDOR_DISABLE_EXT() my_callback_vendor_disable()
 * extern void my_callback_vendor_disable(void);
 *
 * #define  UDI_VENDOR_SETUP_OUT_RECEIVED()  my_vendor_setup_out_received()
 * extern bool my_vendor_setup_out_received(void);
 * #define  UDI_VENDOR_SETUP_IN_RECEIVED()   my_vendor_setup_in_received()
 * extern bool my_vendor_setup_in_received(void);
 */

//! endpoints size for full speed
#define  UDI_VENDOR_EPS_SIZE_INT_FS    64
#define  UDI_VENDOR_EPS_SIZE_BULK_FS   64
#define  UDI_VENDOR_EPS_SIZE_ISO_FS   256

//! endpoints size for high speed
#define  UDI_VENDOR_EPS_SIZE_INT_HS    64
#define  UDI_VENDOR_EPS_SIZE_BULK_HS  512
#define  UDI_VENDOR_EPS_SIZE_ISO_HS    64

/**
 * USB Class Vendor low level configuration
 * In standalone these configurations are defined by the Class Vendor module.
 * For composite device, these configuration must be defined here
 * @{
 */
//! Endpoint numbers definition
#define  UDI_VENDOR_EP_INTERRUPT_IN  (1 | USB_EP_DIR_IN)
#define  UDI_VENDOR_EP_INTERRUPT_OUT (2 | USB_EP_DIR_OUT)
#define  UDI_VENDOR_EP_BULK_IN       (3 | USB_EP_DIR_IN)
#define  UDI_VENDOR_EP_BULK_OUT      (4 | USB_EP_DIR_OUT)
#define  UDI_VENDOR_EP_ISO_IN        (5 | USB_EP_DIR_IN)
#define  UDI_VENDOR_EP_ISO_OUT       (6 | USB_EP_DIR_OUT)


//! Interface number
#define  UDI_VENDOR_IFACE_NUMBER     0
//@}
//@}

//... Eventually add other Interface Configuration

//@}


/**
 * Description of Composite Device
 * @{
 */
//! USB Interfaces descriptor structure
//#define UDI_COMPOSITE_DESC_T

//! USB Interfaces descriptor value for Full Speed
//#define UDI_COMPOSITE_DESC_FS

//! USB Interfaces descriptor value for High Speed
//#define UDI_COMPOSITE_DESC_HS

//! USB Interface APIs
//#define UDI_COMPOSITE_API

// Example for device with cdc, msc and hid mouse interface
#define UDI_COMPOSITE_DESC_T \
	usb_iad_desc_t udi_cdc_iad; \
	udi_cdc_comm_desc_t udi_cdc_comm; \
	udi_cdc_data_desc_t udi_cdc_data; \
	udi_hid_kbd_desc_t udi_hid_kbd
	//udi_msc_desc_t udi_msc; \
	//udi_hid_mouse_desc_t udi_hid_mouse

//! USB Interfaces descriptor value for Full Speed
#define UDI_COMPOSITE_DESC_FS \
	.udi_cdc_iad               = UDI_CDC_IAD_DESC_0, \
	.udi_cdc_comm              = UDI_CDC_COMM_DESC_0, \
	.udi_cdc_data              = UDI_CDC_DATA_DESC_0_FS, \
	.udi_hid_kbd			   = UDI_HID_KBD_DESC
	//.udi_msc                   = UDI_MSC_DESC_FS, \
	//.udi_hid_mouse             = UDI_HID_MOUSE_DESC

//! USB Interfaces descriptor value for High Speed
#define UDI_COMPOSITE_DESC_HS \
	.udi_cdc_iad               = UDI_CDC_IAD_DESC_0, \
	.udi_cdc_comm              = UDI_CDC_COMM_DESC_0, \
	.udi_cdc_data              = UDI_CDC_DATA_DESC_0_HS, \
	.udi_hid_kbd			   = UDI_HID_KBD_DESC
	//.udi_msc                   = UDI_MSC_DESC_HS, \
	//.udi_hid_mouse             = UDI_HID_MOUSE_DESC

//! USB Interface APIs
#define UDI_COMPOSITE_API  \
	&udi_api_cdc_comm,       \
	&udi_api_cdc_data,		\
	&udi_api_hid_kbd
	//&udi_api_msc,            \
	//&udi_api_hid_mouse


//@}


/**
 * USB Device Driver Configuration
 * @{
 */
//@}

//! The includes of classes and other headers must be done at the end of this file to avoid compile error
#include "udi_hid_kbd.h"
#include "udi_cdc.h"
/* Example of include for interface
#include "udi_msc.h"
#include "udi_hid_kbd.h"
#include "udi_hid_mouse.h"
#include "udi_cdc.h"
#include "udi_phdc.h"
#include "udi_vendor.h"
*/
/* Declaration of callbacks used by USB
#include "callback_def.h"
*/

#endif // _CONF_USB_H_